Murci Center Console Limited Run (1 WEEK ONLY 7/30-8/6)

[Tallon]

+1 thanks string!

[String]

This is the Climate control cover and frame so far , got to flatten it out yet...

So just a couple of pics for now...

[pkovgolf]

I need.the hvac cover - mine isn't very well done.
What would yours sell for and would you have details for installing the springs etc?
Thank you!!

[String]

I am looking to do the A/C Lid Double DIN frame soon - which on a side note also employs a couple of lever wound springs , which are of the same type as used in the console hinge - if anyone can source them , I have had no luck.

Hi, I meant I am working on the frame and pieces and have one to copy , the springs are something that everyone will require to make the console lid work and a lighter weight version for the A/C lid.

I have what you are taking about... You need it?

[pkovgolf]

Awesome
Thank you Chris!!

[No Bull]

I'm going to set up a new area for drawings like this.  Please upload these and any others you might have when you get a chance?

Thanks,

Chris

[usmc_butler]

I am looking to do the A/C Lid Double DIN frame soon - which on a side note also employs a couple of lever wound springs , which are of the same type as used in the console hinge - if anyone can source them , I have had no luck.

I have what you are taking about... You need it?

[String]

AWESOME FILES!

I didn't know these existed... please share more!

If you have a lot of these, I can create a spot of the site just for them.

Thank you for sharing String!

Chris

I do drawings as I get my hands on the part , I am looking to do the A/C Lid Double DIN frame soon - which on a side note also employs a couple of lever wound springs , which are of the same type as used in the console hinge - if anyone can source them , I have had no luck.

Today I have the dash button frame which holds the trim rings around the switch buttons.
 

[No Bull]

At $19 a piece for the rears I'll probably go with a substitute on my car and use a pair of adjustable stoppers from under the hood of a donor car.  The front cushions I'll use OEM since I have one of Texas's inner finish panels like Tallon showed in his picture and this will give it a nice finished look.

Thanks for sharing the part numbers guys!

Chris

[BigPines]

Thanks guys. This really is an AMAZING place!

[autopro]

The ones for the rear show a different part number: 417807333

You can see them in this picture and they are different.

[No Bull]

Are these the same part in the front and the back? So we need four total? Two for the front hood and two for the rear engine lid?

Great question and I don't recall seeing them in the engine compartment which doesn't mean they are not there (probably just not as noticeable).  I decided against putting a lot of OEM appearing or original parts in the engine compartment just because the engine is first indication that the car is a replica when the engine cover is up however since you need something back there anyhow to cushion the cover, at $14 a pair you'd be lucky to come up with a decent donor at that price.

Chris

[BigPines]

Are these the same part in the front and the back? So we need four total? Two for the front hood and two for the rear engine lid?

[No Bull]

Awesome.. thanks guys.  I have them on order already.  I seen them on my buddies car the other day and wanted to order them but could only see the part number for the cushions and thought there might be more to it since they were only $6.00.  For a Lamborghini OEM part... these are a bargain for what you actually get!   

Chris

[autopro]

AUDI or Lambo part no. 8L0827249 , one piece component, just add pop rivets.

For some reason they are much cheaper to buy through Lambostuff than through a VW dealership, go figure.  Lambostuff price on them is $6.00

This is how they come: