« previous next »
Pages: 1 ... 29 30 [31] 32 33 ... 57

Author Topic: G28 - Simple Mans, Simple REDO of an G28 LP640  (Read 190179 times)

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #402 on: June 06, 2018, 11:33:43 PM »
Working on my bumper...which side marker light ::scratch
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #401 on: June 05, 2018, 11:45:18 PM »
The HID H3 bulb connectors came in the mail today . 

The Hella Micro DE is the projector that I am using for my fog lights

An aluminum bracket was made to hold the bulb in place, using the existing screws, as the base of the HID bulb is longer than the halogen
« Last Edit: June 06, 2018, 12:23:18 AM by Simple Man »
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #400 on: June 05, 2018, 11:28:49 PM »
Quote from: m-will on June 04, 2018, 09:29:49 AM
Excellent work  ::salute

Thanks M-will!!
Logged

m-will

  • Trade Count: (+1)
  • Jr. Member
  • **
  • Posts: 11
  • Liked: 5
  • Member Rating Points: +0/-0
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #399 on: June 04, 2018, 09:29:49 AM »
Excellent work  ::salute
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #398 on: June 03, 2018, 10:50:29 PM »
Both headlights are finally done  8)  They easily go in and out of the car, and the electrics connect and disconnect quickly.

Just need the H3 bulb connectors, Do final test and then store in a safe place   :o

Pretty happy with how they turned out. A bit of time was spent on these, for sure  :LL:
« Last Edit: June 03, 2018, 10:57:35 PM by Simple Man »
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #397 on: June 03, 2018, 10:44:05 PM »
The old exhaust didnt have a flex pipe in it so one was purchased.

It hung down too low and didn't line up with the opening in the back of the car. After making a few measurements,  the pipe was cut and welded back together.

Turned out pretty decent and lines up well.

Just need to mount the metal replica LP640 exhaust tip...after I REDO the finish and make a bracket to mount the tip  ::toothy
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #396 on: May 31, 2018, 08:16:15 PM »
While waiting on my H3 bulb plugs the H1 ballast and relays were mounted

Wanted to clean up the wiring in the front trunk.  I used the same wire loom wrap that the HID system came with.

Before and after Pictures. you can see all the HID wiring laying there :LL:

Much better! ::toothy
« Last Edit: May 31, 2018, 08:19:30 PM by Simple Man »
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #395 on: May 30, 2018, 09:33:53 PM »
ahhhh!! my gal made me a nice cocktail after that mind numbing wiring....

Oh gee! The drivers side is almost ready to wire up :LL: :o
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #394 on: May 30, 2018, 09:12:49 PM »
With the signals working, Time to get the headlights up and running.

The morimoto system is pretty straight forward and worked right out of the box in a quick test using the Fiero wiring and Sebring steering column

My projector has a shutter and was wired to the high beam switch.

I'm using a 13 pin trailer plug to run all my wiring into the headlight enclosure. For some reason the HID light would not work using this plug so the two wires were ran through the headlight housing.  These holes will be sealed later.

 It was very tedious and took some time to test each connection into and out of the Plug.  It will make it quicker to remove the headlight unit from the car.   

Shout to Murci-Me for some guidance on the signal, test tube and side marker light wiring 8) ::salute

The fog light will be controlled from the dash switch to the left of the Steering.  As usual need one part to complete this.  ::toothy
« Last Edit: May 30, 2018, 09:19:04 PM by Simple Man »
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #393 on: May 19, 2018, 01:47:41 PM »
Quote from: Purple LP670 SV on May 18, 2018, 05:57:25 PM
Nice work fella!  ::beers

Thanks! Talked to the PO, it appears that the hazard lights were not working.... so have to sort that out now :)
Logged

Purple LP670 SV

  • Lambo Mafia
  • Global Moderator
  • Trade Count: (+11)
  • Hero Member
  • *****
  • Posts: 738
  • Liked: 649
  • Member Rating Points: +23/-0
  • Big Gulps, huh? All right! Well, see ya later.
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #392 on: May 18, 2018, 05:57:25 PM »
Nice work fella!  ::beers
Logged
I met a man with a dollar, we exchanged dollars and we still had a dollar. I met a man with an idea, we exchanged ideas and now we both have two ideas!!!

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #391 on: May 15, 2018, 08:18:35 PM »
Well that took a while.... but The problem with the signals was tracked down and resolved  ::toothy
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #390 on: May 10, 2018, 07:41:23 PM »
Just came back from a visit down to OKC.  Just getting back to the REDO.

I have an issue with the signals. Running lights work great.  Test light lights, going into the flasher is super bright, but coming out it is rather dim regardless of the signal switch is in the on or off position.

There is power coming out of the signal switch for left and right, when turned on just no signal.  I think I have a ground issue or continuity issue.   ::scratch
Logged

Simple Man

  • Guest
  • Trade Count: (0)
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #389 on: May 10, 2018, 07:23:03 PM »
Quote from: lambobuilder on May 03, 2018, 09:01:40 AM
I do believe I recognize those printed instructions.  ::tongue  If you don't have the Fiero Haynes manual I think you can download from here http://www.fieronews.net/fusion/downloads.php



Yes I have read a lot of your info from your website!  thank you!!

Got few more of the connectors identified from a post I put on pennocks.
Logged

lambobuilder

  • Trade Count: (0)
  • Sr. Member
  • ****
  • Posts: 267
  • Liked: 211
  • Member Rating Points: +17/-0
    • Lambobuilder
Re: G28 - Simple Mans, Simple REDO of an G28 LP640
« Reply #388 on: May 03, 2018, 09:01:40 AM »
I do believe I recognize those printed instructions.  ::tongue  If you don't have the Fiero Haynes manual I think you can download from here http://www.fieronews.net/fusion/downloads.php

Logged
Pages: 1 ... 29 30 [31] 32 33 ... 57
« previous next »