Author Topic: Bonding headlight lenses.  (Read 4107 times)

nickmkk

  • Trade Count: (+4)
  • Full Member
  • ***
  • Posts: 217
  • Liked: 61
  • Member Rating Points: +5/-0
  • Cloquet, MN
Re: Bonding headlight lenses.
« Reply #8 on: October 17, 2016, 11:43:38 AM »
I was liking the idea of using strips because I could temporarily attach the lens then fabricate the mounts for the headlights.  I'll just wait to mount the headlights until I've finished building them though.  Then I can attach the lens with urethane and mount them so the lens will definitely be flush with the fenders.
 ::beers

autopro

  • Lambo Mafia
  • Administrator
  • Trade Count: (+28)
  • Hero Member
  • *****
  • Posts: 1425
  • Liked: 1204
  • Member Rating Points: +43/-1
  • Tijuana/San Diego
Re: Bonding headlight lenses.
« Reply #7 on: October 17, 2016, 09:16:44 AM »
If you are bonding the lenses to the buckets I would just use the windshield urethane.
Pedro

nickmkk

  • Trade Count: (+4)
  • Full Member
  • ***
  • Posts: 217
  • Liked: 61
  • Member Rating Points: +5/-0
  • Cloquet, MN
Re: Bonding headlight lenses.
« Reply #6 on: October 15, 2016, 06:33:44 PM »
Sorry if this seems like a stupid question but how hard should the rubber be for this? Would 40 Shore A work or should I go softer?  Is there something specific that you use for this or do you just buy a sheet of rubber material and cut it into strips?

just bond rubber strips to the buckets and then screw the lense down to seal them
« Last Edit: October 15, 2016, 06:41:15 PM by nickmkk »

Digibeam

  • Trade Count: (+2)
  • Sr. Member
  • ****
  • Posts: 445
  • Liked: 257
  • Member Rating Points: +12/-0
  • Show me, don't Tell me...
Re: Bonding headlight lenses.
« Reply #5 on: August 06, 2014, 11:49:38 AM »
Why can't he just use a foam gasket then use wrap around clips on the edges?

Matty99dun

  • Trade Count: (+2)
  • Full Member
  • ***
  • Posts: 100
  • Liked: 22
  • Member Rating Points: +0/-0
Re: Bonding headlight lenses.
« Reply #4 on: August 06, 2014, 03:57:16 AM »
if you get lenses with sides they should have a flat edge around the outer, you screw this edge it fits under the panel so you can't see any
 screws, I guess it depends on what lenses you have. .

am33r

  • Trade Count: (0)
  • Sr. Member
  • ****
  • Posts: 376
  • Liked: 37
  • Member Rating Points: +1/-0
  • YOLO
Re: Bonding headlight lenses.
« Reply #3 on: August 05, 2014, 01:30:42 PM »
bond rubber strips to the buckets and then screw the lense down to seal them

But then you will have to drill the lenses and have visible screws on the surface of the headlight lens!

At this time are your buckets fiber-glassed to the kit or are they removable?

You have 3 parts: Bucket, Lens, Kit.  I would say bond the 2 visible Parts and the bucket should be removable.  Or, bond the lens to the bucket but allow for it to full resulting headlight to drop into place on the kit and mount.
« Last Edit: August 05, 2014, 01:36:12 PM by am33r »

Matty99dun

  • Trade Count: (+2)
  • Full Member
  • ***
  • Posts: 100
  • Liked: 22
  • Member Rating Points: +0/-0
Re: Bonding headlight lenses.
« Reply #2 on: August 05, 2014, 06:58:52 AM »
I wouldn't bond them at all just incase you need to remove the lense for cleaning inside the head light buckets, just bond rubber strips to the buckets and then screw the lense down to seal them, it might also be a good idea to drill two small holes at the front of the buckets to let moisture out as done on OEM, see the tubes in picture.

notnilc20

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 514
  • Liked: 174
  • Member Rating Points: +16/-0
Bonding headlight lenses.
« Reply #1 on: July 14, 2014, 05:41:53 PM »
Just wanted to know what is the best adhesive to use when bonding the headlight lenses to the car? All purpose auto weatherstripping adhesive? Or the urethane windshield bond stuff?