Author Topic: Murci Console Parts  (Read 1812 times)

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1257
  • Member Rating Points: +18/-5
Re: Murci Console Parts
« Reply #9 on: December 11, 2013, 06:47:21 PM »
here's an oem pic for reference

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1257
  • Member Rating Points: +18/-5
Re: Murci Console Parts
« Reply #8 on: December 11, 2013, 07:01:29 AM »
that helps thanks guys!  :santa

Anyone know what kind of springs are needed? It looks like it holds the lid closed until it's pulled back then it holds it open.
« Last Edit: December 13, 2013, 07:06:20 AM by Tallon »

autopro

  • Lambo Mafia
  • Administrator
  • Trade Count: (+28)
  • Hero Member
  • *****
  • Posts: 1200
  • Member Rating Points: +32/-1
  • Tijuana/San Diego
Re: Murci Console Parts
« Reply #7 on: December 10, 2013, 04:08:18 PM »
Here are some PDF's, they are printed on 11x17 size paper.  The measurements on there have been rounded to the nearest 1/8" since String's drawings where in mm. and I converted them.

Thanks String for providing those sketches  :notworthy

« Last Edit: December 10, 2013, 04:46:00 PM by autopro »
Pedro

SchulzeA

  • Global Moderator
  • Trade Count: (+15)
  • Hero Member
  • *****
  • Posts: 573
  • Member Rating Points: +32/-1
  • Lambo Mafia
Re: Murci Console Parts
« Reply #6 on: December 10, 2013, 03:38:50 PM »
 :occasion  ::thumbup

String

  • Trade Count: (+6)
  • Full Member
  • ***
  • Posts: 249
  • Member Rating Points: +19/-0
Re: Murci Console Parts
« Reply #5 on: December 10, 2013, 03:14:33 PM »
Flattened ! , of course ..... thanks to those who pointed this out.

Oooh , new smileys   W:)
« Last Edit: March 03, 2015, 03:24:48 PM by String »
Oooh , Red leather.

autopro

  • Lambo Mafia
  • Administrator
  • Trade Count: (+28)
  • Hero Member
  • *****
  • Posts: 1200
  • Member Rating Points: +32/-1
  • Tijuana/San Diego
Re: Murci Console Parts
« Reply #4 on: December 10, 2013, 12:50:28 PM »
is there any way to flatten any of the separate pieces in sketchup? like undo all the bends?

I suck at sketchup but I imported it into Revit and I am working on that.  I'll see if I can get some templates up today or tomorrow.
Pedro

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1257
  • Member Rating Points: +18/-5
Re: Murci Console Parts
« Reply #3 on: December 10, 2013, 11:20:41 AM »
is there any way to flatten any of the separate pieces in sketchup? like undo all the bends?

usmc_butler

  • Lambo Mafia
  • Administrator
  • Trade Count: (+11)
  • Hero Member
  • *****
  • Posts: 1658
  • Member Rating Points: +33/-0
  • Mafia Productions
    • Lambo Mafia
Re: Murci Console Parts
« Reply #2 on: December 10, 2013, 08:34:32 AM »
Here are a couple pictures of the one I have from a burnt Murci.



No Bull

  • Administrator
  • Trade Count: (+25)
  • Hero Member
  • *****
  • Posts: 1108
  • Member Rating Points: +20/-0
  • Replication is the sincerest form of flattery
Murci Console Parts
« Reply #1 on: December 09, 2013, 08:12:38 PM »
Thanks to String for providing these in another thread.

Use Sketchup to open these.

Chris