« previous next »
Pages: 1 ... 4 5 [6]

Author Topic: Interior and Exterior door handles  (Read 24237 times)

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #13 on: July 05, 2012, 08:53:19 PM »
 ::scratch that is oem it's just that the oem shoulder is a little wider
all other measurements are correct

oem even has the angle
« Last Edit: July 05, 2012, 09:02:09 PM by Tallon »
Logged

Onewickedsvt

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 225
  • Liked: 18
  • Member Rating Points: +3/-0
Re: Door latch handle
« Reply #12 on: July 05, 2012, 08:04:33 PM »
I need oem style! Help!
Logged

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #11 on: July 05, 2012, 06:08:43 PM »
That's what I was looking for thanks

$26 at mcmaster
everywhere else expensive O_O
« Last Edit: July 05, 2012, 08:58:43 PM by Tallon »
Logged

SchulzeA

  • Guest
  • Trade Count: (0)
Re: Door latch handle
« Reply #10 on: July 05, 2012, 05:48:50 PM »
 ::salute
You need a ball nose endmill. Clamp the part in a vise and use a drill press to create the dimple. Or use a bridgeport style mill if you have access to one.
Logged

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #9 on: July 05, 2012, 05:26:02 PM »
found it
this is for narrow g28, oem would be wider.

from murcie me as well I'm guessing correct me if I'm wrong


Ok it took awhile for me to search for this.. do you get the circle in there with a "Freud Round Nose Bit"?
« Last Edit: July 05, 2012, 05:44:21 PM by Tallon »
Logged

usmc_butler

  • Lambo Mafia
  • Administrator
  • Trade Count: (+11)
  • Hero Member
  • *****
  • Posts: 1677
  • Liked: 418
  • Member Rating Points: +33/-0
  • Mafia Productions
    • Lambo Mafia
Re: Door latch handle
« Reply #8 on: July 05, 2012, 04:50:01 PM »
Good find Tallon! Maybe Mike will move that over here for a better local reference! ::thumbup
Logged

SchulzeA

  • Guest
  • Trade Count: (0)
Re: Door latch handle
« Reply #7 on: July 05, 2012, 03:43:10 PM »
 ::rocker
Logged

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #6 on: July 05, 2012, 02:10:33 PM »
http://www.madmechanics.com/forum/technical-discussion-question/11568-murcie-door-handles-101-a.html
shows measurement as for where to place the handle.
and murcie-me's latch & pocket
« Last Edit: July 05, 2012, 02:13:02 PM by Tallon »
Logged

SchulzeA

  • Guest
  • Trade Count: (0)
Re: Door latch handle
« Reply #5 on: July 05, 2012, 01:57:25 PM »
jb1, thank you!
Logged

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #4 on: July 05, 2012, 01:23:41 PM »
I think the measurments I have are from murcie-me, a lot of his older stuff is still under the pile at MM. Including the pocket the latch sits in. I'd like to know what is needed to make the actual mechanism, though.
« Last Edit: July 05, 2012, 01:25:31 PM by Tallon »
Logged

jb1

  • Trade Count: (+2)
  • Full Member
  • ***
  • Posts: 80
  • Liked: 0
  • Member Rating Points: +0/-0
Re: Door latch handle
« Reply #3 on: July 05, 2012, 01:20:26 PM »
Ill take measurements  and post few pics  of mine,  yes they  are very simple  to make ,,,   I bought mine  from Lambochic  over on MM  but after I got them it was  like  ,  "why didn't I just make these?"   but  I did not have measurements etc...
Logged

Tallon

  • Trade Count: (+4)
  • Hero Member
  • *****
  • Posts: 1269
  • Liked: 188
  • Member Rating Points: +18/-5
Re: Door latch handle
« Reply #2 on: July 05, 2012, 11:48:57 AM »
It seems like the oem handle is simple to make and the dimensions for it are all over the place so why not
An alternative for the interior would be nice, though, and it looks like something like this would probably work. Can't tell how big it is, though.
« Last Edit: July 05, 2012, 11:50:40 AM by Tallon »
Logged

SchulzeA

  • Guest
  • Trade Count: (0)
Interior and Exterior door handles
« Reply #1 on: July 05, 2012, 10:49:25 AM »
What handles are people using on the exterior of the car? I seen the c3 corvette is a similar design. It appears to be a bit to large but I wonder if it can be reworked to fit...
« Last Edit: April 22, 2013, 08:22:38 AM by usmc_butler »
Logged
Pages: 1 ... 4 5 [6]
« previous next »