« previous next »
Pages: 1 ... 8 9 [10] 11 12 ... 16

Author Topic: 3D printed Aventador  (Read 47590 times)

autopro

  • Lambo Mafia
  • Administrator
  • Trade Count: (+28)
  • Hero Member
  • *****
  • Posts: 1425
  • Liked: 1204
  • Member Rating Points: +43/-1
  • Tijuana/San Diego
Re: 3D printed Aventador
« Reply #95 on: November 05, 2018, 06:15:19 PM »
Man you did well getting all those angles perfect, not an easy thing to do, that structure looks pretty awesome.
Logged
Pedro

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #94 on: November 04, 2018, 01:05:03 PM »
Finished tacking the engine cover structure.
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #93 on: November 02, 2018, 05:19:56 PM »
Engine cover structure, and rear window structure.
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #92 on: October 29, 2018, 02:10:49 PM »
Fixed the bubbles in the rear bumper (White x's) to get ready for the final CF layer, which will be hand laid.  Also noticed that the passenger side hub was off by ~1" from the center line.  After considering harikari, I noticed my A arm tabs were not quite square with the frame.  ::tongue  A little adjustment and I should be squared up again.  Just goes to show you need to constantly measure, and not be afraid to fix these issues!  ::headbang
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #91 on: October 29, 2018, 02:01:52 PM »
Bonded the sail panels to the quarters, and now have the quarter panel mounts solid.  I can actually lean on it now! ::rocker
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #90 on: October 23, 2018, 01:46:34 PM »
This weekends fun! Sill, and B pillar structure.  Sail panel understructure done, and dash hood printed.
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #89 on: October 21, 2018, 05:23:12 PM »
It is, but I am in this for the fun of solving problems, so all good! W:)
Logged

LP700-4

  • Trade Count: (+1)
  • Full Member
  • ***
  • Posts: 84
  • Liked: 43
  • Member Rating Points: +2/-0
Re: 3D printed Aventador
« Reply #88 on: October 21, 2018, 09:20:20 AM »
Sounds like a lot of work to use the off the shelf hinges nut I agree, $1000 for a set of OEM is crazy!
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #87 on: October 21, 2018, 08:24:10 AM »
I will also need to put in some hinge guides to make sure the door opens at the right angle to clear the front of the window.  It is better than blowing $1k on an original set.  :o
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #86 on: October 20, 2018, 07:14:15 PM »
One of those lambo door conversion units, about $99.  I have heavily modified it.  Currently it is inside the door, so as I add door structure, I can have it bolt to the front of the door.
« Last Edit: October 20, 2018, 07:20:06 PM by Footcutter »
Logged

LP700-4

  • Trade Count: (+1)
  • Full Member
  • ***
  • Posts: 84
  • Liked: 43
  • Member Rating Points: +2/-0
Re: 3D printed Aventador
« Reply #85 on: October 20, 2018, 06:45:55 PM »
What did you use for a hinge?
Logged

Theoneabove

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 60
  • Liked: 7
  • Member Rating Points: +1/-0
Re: 3D printed Aventador
« Reply #84 on: October 20, 2018, 02:00:53 PM »
Quote from: Footcutter on October 20, 2018, 01:53:35 PM
Morning fun! Door structure.
Very impressive! Keep up the great work.
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #83 on: October 20, 2018, 01:53:35 PM »
Morning fun! Door structure. 
Logged

Footcutter

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 245
  • Liked: 142
  • Member Rating Points: +11/-0
    • 3D car printing
Re: 3D printed Aventador
« Reply #82 on: October 16, 2018, 07:32:03 PM »
Thanks!  ::thumbup
Logged

LP700-4

  • Trade Count: (+1)
  • Full Member
  • ***
  • Posts: 84
  • Liked: 43
  • Member Rating Points: +2/-0
Re: 3D printed Aventador
« Reply #81 on: October 16, 2018, 10:11:14 AM »
looking good and making great progress
Logged
Pages: 1 ... 8 9 [10] 11 12 ... 16
« previous next »