« previous next »
Pages: 1 ... 4 5 [6] 7 8 9

Author Topic: Eddies Diablo build  (Read 38988 times)

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #47 on: June 24, 2019, 05:13:06 AM »
 friend of mine wired the light bar for me ,so if you interested here are the diagram how to . I think original in cars are by ECM??
anyway here
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #46 on: June 08, 2019, 02:17:02 PM »
door vent from Milton
keep in mind this is just rough body and prime so I can see in imperfections
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #45 on: June 04, 2019, 09:21:31 AM »
Oh forgot new two piece dash board from Marcello
And light bar
I just don’t have time to spend hours to fix I rather buy one new that fits .
Oh speaking about the light bar as I asked everywhere
How to hoop up that idiot lights so when you turn key on they all light up and shut off in 3 seconds just like any  car
So I put two pos wires on each and one that goes to each signal meaning
Second put all together and run on ignition  on with delay diode , Bada bum bada bim
« Last Edit: June 04, 2019, 11:03:19 AM by eddie »
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #44 on: June 04, 2019, 09:13:29 AM »
Misker it depends how your skills are
To me everything is complicated specially when you get bad slashed body
I had to buy set of new door shells from Ron , then the A post was not accurate to new doors , lot re dos , side inner panels where made for Fiero
Again re do, rocker panels twisted like pretzel
Bought new set from Ron
Etc I’m doing the build as hobby not that I need to drive it next day.
10 years in to it and I could buy B/N high end car for the money I spend on it. But I won’t give up
Logged

Misker

  • Trade Count: (0)
  • Newbie
  • *
  • Posts: 1
  • Liked: 0
  • Member Rating Points: +0/-0
Re: Eddies Diablo build
« Reply #43 on: June 04, 2019, 08:45:43 AM »
Do the handle and arm rest complicate things a lot? Nice work btw, Eddie!
Logged
People are happy with sausage stuffers and use them a lot.

01Lambiero

  • Global Moderator
  • Trade Count: (+1)
  • Hero Member
  • *****
  • Posts: 1168
  • Liked: 407
  • Member Rating Points: +24/-3
  • "Using the skills that God gave me"
Re: Eddies Diablo build
« Reply #42 on: June 03, 2019, 12:14:35 PM »
Don't forget to put water drain holes in the bottom of the door inners.

01
Logged
20 yr. GM Niase certified Auto Mechanic (Tune-Up, Brakes, & Heavy Repair)
24 yr. GM Automated/Robotic Welding Systems
Retired

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #41 on: June 03, 2019, 09:05:52 AM »
I do I just took it off to add the vents in doors from Milton
I’m working on only on weekend due to my busy  14 hours a day
Logged

diablodoc

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 76
  • Liked: 29
  • Member Rating Points: +2/-0
Re: Eddies Diablo build
« Reply #40 on: June 03, 2019, 08:44:41 AM »
Looking good Eddie.  You and I are about neck and neck in the build progress.  Do you have your doors done?
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #39 on: June 02, 2019, 10:48:07 AM »
dash cluster just  placed on not bolted
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #38 on: June 02, 2019, 10:38:36 AM »
  did did little 2k priming so I can see better the lines, gaps, some body improve etc.
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #37 on: May 19, 2018, 07:53:59 PM »
 made my head light bracket , it can  adjust left or right up or down . btw I had the original plate and somehow I tossed in scrap bin at work  >:(
 needs bit of body work around and then lock it in , oh head light unit will be epoxy glued to plate by 3M 8115. I can unsrew and remove if need it.
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #36 on: May 13, 2018, 01:27:01 PM »
this just cheap U pol lacquer primer after all is done the go again panel by panel with polyester filler then 2K . doing it so I can see the lines and low/high spot for now.
Logged

autopro

  • Lambo Mafia
  • Administrator
  • Trade Count: (+28)
  • Hero Member
  • *****
  • Posts: 1425
  • Liked: 1204
  • Member Rating Points: +43/-1
  • Tijuana/San Diego
Re: Eddies Diablo build
« Reply #35 on: May 13, 2018, 11:59:43 AM »
Looking good, it's nice to get primer on parts because it feels like real progress.
Logged
Pedro

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #34 on: May 13, 2018, 10:51:22 AM »
so back work on again
did finished  tail lights pods, fab mounting brackets and start do some body work on left side , exhaust deck done too. pods, grille just placed not bolt on yet.
Logged

eddie

  • Trade Count: (+2)
  • Hero Member
  • *****
  • Posts: 891
  • Liked: 291
  • Member Rating Points: +19/-2
Re: Eddies Diablo build
« Reply #33 on: January 30, 2018, 04:26:22 PM »
member on asked about my center console. I could not post picture in PM so here's it
Logged
Pages: 1 ... 4 5 [6] 7 8 9
« previous next »