Orange SuperBass Roadster LP700-4U

[italianknightrider]

PM sent , they are electronic but have needle arms on front to move over the gauge face ,and not digital movement

[Jackal]

check your PM box , i have them set up for the color posted an white face Oem gauge pod will work ,the sheet size is set up for anolog dials ,not the electronic ,i will measure it when i go to the shop

Hi IKR,
Just wanted to clear up a thing or two. You say it is analogue and not electronic. Sorry for my ignorance, I have as you know the RS4 engine with 01E gearbox. Complete RS4 wiring harness. This would mean I have need for electronic setup right? Or could I still use the analogue way. Sorry I have no knowledge of this.

I realize the tacho would most probably run from the coils right?

Regards
jackal

[italianknightrider]

Just posted pictures of the SuperBass Roadster rear clip molds on the last page of this thread 

[italianknightrider]

the real car has a digital display so it show one at a time ,i put all of them on one gauge face to show all of them at the same time.



3 doors




FIBERGLASS

SuperBass rear wing

rear engine cover out of the mold

[Jackal]

check your PM box , i have them set up for the color posted an white face Oem gauge pod will work ,the sheet size is set up for anolog dials ,not the electronic ,i will measure it when i go to the shop

I will be building my own dash etc, centre console, the works. So the unit you have in the pic looks perfect. Just wanted size so that I know what I am looking at. I read your pm, thanks for that. I am interested but have no knowledge of this kind of thing. I learn as I go on. My engine is an Audi Rs 4 4.2 litre with wiring harness and ecu's. Not sure how the hookup works. The setup really looks stunning

[italianknightrider]

check your PM box , i have them set up for the color posted an white face Oem gauge pod will work ,the sheet size is set up for anolog dials ,not the electronic ,i will measure it when i go to the shop

[Jackal]

i could have them make one ,i was not going to make any on this model because i still have 25 for the Murcie , one went to New Zealand

How much would that cost and what are the dia size of the dials? 

Thank you.

Jackal

[italianknightrider]

i could have them make one ,i was not going to make any on this model because i still have 25 for the Murcie ,320kph, one went to New Zealand ,the Murcie kits are just about over to many sellers ,    ... build the newest KIT out ,if the chassis is the same or close ,why put a old body over your new chassis. Real question ,would you get more money for a Murcie or a SuperBass on your chassis today !!

[Jackal]

SuperBass gauge face art work has been completed ,they will make the first run in white ,not black back ground ,an i also have 2 other gauge face art work was completed as well ,just hang on guys they will run them next week , the SuperBass dash an pod should be done in 2 weeks ,i will post pictures of it

SuperBass Gauge Face

simple an Fiero friendly for S10 gauges

you saw this first at LamboClone.com 11-30-2012

Those clocks are really nice. Do you get those up to 320km/hr though? Are those clocks mph?

How much is a cluster like that?

Cheers
Jackal

[italianknightrider]

One piece rear clip with lower diffusor an built in tail lights

side skirts
Doors



3 doors

[italianknightrider]

wild color almost too much stuff added to the car ,i like the front fender vents an carbon fiber under the side skirts an roof





Coupe available too !! 

[italianknightrider]

here are the headlight & taillight lens covers ,this is a 4 coat process that encapsulate the foam lens cover plugs an then they are use to make the lens covers directly over the pattern

START WITH THE BEST FORGET THE REST !!    Saving money up front mean hunting parts forever to finish up, go with the built-in trim components : IKR SuperBass

One piece rear clip with lower diffusor an built in tail lights

 

[italianknightrider]

SuperBass gauge face art work has been completed ,they will make the first run in white ,not black back ground ,an i also have 2 other gauge face art work was completed as well ,just hang on guys they will run them next week , the SuperBass dash an pod should be done in 2 weeks ,i will post pictures of it

SuperBass Gauge Face

simple an Fiero friendly for S10 gauges

you saw this first at LamboClone.com 11-30-2012

[italianknightrider]

Did some trial fitting today to see how the SuperBass Front Cap look on the stretch Fiero



misspell word sorry

[italianknightrider]

Roadster

IKR Kustoms: SuperBass Roadster

1 PC GAUGE FACE

106.3"WB